If a pipe has burst right now, do these three things first:
- Shut off the main water valve. Turn a round handle clockwise until it stops.
- Stay away from electrics if water is near them. Don’t touch outlets, switches, or the panel while standing in or near water.
- Call a licensed plumber and take photos of the damage before you start cleaning up.
The rest of this page walks through each step, what to avoid, and how to make the next burst less likely.
It rarely freezes in the San Fernando Valley, so a burst here usually isn’t a winter problem. It’s a pipe that was already aging, running at high pressure, or corroding from the inside. That’s good to know, because it means the warning signs are often there weeks before the failure.
Your first 10 minutes
- Close the main shutoff valve. In most Valley homes it’s where the water line enters the house, often on the front or side wall near a hose bib, or inside the garage. A round gate-valve handle turns clockwise until it stops. A lever handle turns a quarter turn so the lever sits crosswise to the pipe. Many homes also have a valve in the meter box near the curb, but use the one at the house if you can reach it. Not sure which valve is the main? Call us and we’ll talk you through it.
- Check the electrics before you do anything else. If water is reaching outlets, dripping through a light fixture, or pooling near the panel, don’t touch switches, outlets, or the panel, and don’t stand in the water. Keep everyone out of that area. If the panel is in a dry spot and you don’t have to step through water to reach it, you can switch off the breakers for the affected rooms. Otherwise leave it for a licensed pro.
- Turn off the water heater. Gas: turn the control to “pilot” or “vacation.” Electric: switch off its breaker (same dry-panel rule as above). This keeps the heater from running while the supply is shut off and the lines are draining. If it’s leaking or acting up, see water heater repair.
- Drain the lines. With the main closed, open the lowest faucet in the house or an outdoor hose bib so the remaining water drains out and the leak slows.
- Contain the water. Put towels at doorways, push water toward a floor drain or outside with a squeegee, and use a wet/dry vacuum if you have one. Lift rugs and move electronics and furniture out of the wet area.
- Document everything. Take photos or a short video before you clean up, and keep damaged items until your insurance adjuster has seen them.
- Smell gas? Leave first. Get everyone, including pets, out of the house. Call 911 or SoCalGas at 1-800-427-2200 from outside. Don’t flip switches or use anything that could spark. Once the utility says it’s safe, our gas line repair safety guide explains what comes next.
- Call a licensed plumber. The sooner the leak is repaired, the less drying and rebuilding you’ll face. Call your insurance company too and ask what they require for water mitigation.
- Start drying. Open windows and run fans once it’s electrically safe. Mold can start growing within 24 to 48 hours in damp materials, so don’t let wet carpet or drywall sit.
If it’s sewage, not clean water
A backup from a floor drain, shower, or tub is a different problem from a burst supply line. Don’t run water or flush toilets, and avoid contact with the water. Find your clean-out cap (usually near the front or side of the house) so the plumber can get to the line quickly. Not sure whether a camera inspection, snaking, or hydrojetting is the right fix? See hydrojetting vs. snaking.

Why pipes burst in Valley homes
- Age and material. Older homes may still have galvanized steel, which corrodes from the inside. Some homes built from the late 1970s into the 1990s have polybutylene piping, which is known for failing without much warning.
- High water pressure. Pressure above roughly 80 psi stresses fittings, supply lines, and appliance connections. A failed or missing pressure-reducing valve is a common cause.
- Hard water and scale. Valley water is hard. Scale buildup shortens the life of heaters, valves, and pipes.
- Slab and ground movement. Many Valley homes are built on slabs with pipes running beneath them. Settling and earthquakes can strain those lines.
- Cheap or worn connections. Rubber washer hoses, old supply lines, and aging shutoff valves fail more often than the pipes themselves.
What not to do
- Don’t cut into walls or ceilings to look for the leak. Keep people clear of a bulging ceiling; a plumber can handle it safely.
- Don’t relight a pilot light if you smelled gas.
- Don’t pour chemical drain cleaners into a backed-up drain. They can burn skin and damage pipes.
- Don’t run a rental snake through old clay or fragile lines. Breaks are common in older homes.
- Don’t turn the water back on to “see if it holds.” Wait for the plumber’s go-ahead, then open the valve slowly.
What a plumber does when they arrive
- Safety check. Confirm that gas and power are safe.
- Locate the leak. Moisture meters, thermal imaging, and acoustic tools can find a leak without opening up the whole wall. See leak detection and repair.
- Stop it. A temporary cap, reroute, or valve replacement stops the water so you can turn the main back on.
- Protect the home. Pump standing water and lay down floor protection.
- Explain your options and price before work starts. Usually that’s a spot repair, a reroute, or, if the pipes are failing throughout, repiping.
Signs of a hidden leak
Not every leak announces itself. Watch for these:
- A water bill that jumps with no change in how you use water
- The sound of running water when everything is off
- Warm spots on the floor, or damp carpet or baseboards
- A musty smell, or low water pressure
Quick check: turn off every faucet and appliance that uses water, then look at your water meter. If the low-flow indicator is still moving, water is going somewhere between the meter and your fixtures.
How to prevent the next one
- Know and label your shutoffs. Everyone in the house should know where the main is.
- Exercise the main valve once a year. Old valves seize. If yours won’t turn fully, replace it before you need it in an emergency.
- Check your water pressure. A cheap gauge on a hose bib tells you. If it’s regularly above about 80 psi, ask about a pressure-reducing valve.
- Replace rubber washer and ice-maker hoses with braided stainless steel lines.
- Brace your water heater and consider a seismic shutoff valve. See do I need a seismic gas shutoff? and earthquake plumbing prep in Los Angeles.
- Get a plumbing inspection if your home has galvanized or polybutylene pipes, or you’ve had more than one leak.
FAQs
Does homeowners insurance cover a burst pipe?
Many policies cover sudden and accidental water damage, but not damage from slow leaks or neglected maintenance. Whether the pipe repair itself is covered varies by policy. Call your insurer right away, and keep your photos and the plumber’s invoice.
Can I turn the water back on after a temporary fix?
Only after the plumber says it’s safe. Open the main slowly and check for drips at the repair and at other fixtures before you leave it on.
How do I know if the leak is under the slab?
Unexplained high bills, the sound of running water, warm floor spots, and a moving meter indicator with everything off are the usual signs. A plumber can confirm the location with acoustic or thermal tools before anything is opened up.
How long do I have before mold starts?
Mold can begin growing in 24 to 48 hours in damp materials. Remove standing water, run fans, and get wet carpet and drywall dried or removed quickly.
Who do I call after hours?
For an active leak, call us at 818-941-6741 and we’ll walk you through the shutoff steps while we get to you. For non-urgent work, book online.
Need help with a burst pipe?
Hi-Tech Plumbing Services Inc. is based at 20407 Parthenia St in Winnetka and serves the Valley and the rest of Los Angeles. For an active leak, see our emergency plumber service or call 818-941-6741.